> >>GY-21V3-SHT20 SHT20 Hőmérséklet és páratartalom érzékelő modul Breakout átalakító
Alacsonyabb ár! GY-21V3-SHT20 SHT20 Hőmérséklet és páratartalom érzékelő modul Breakout átalakító Nagyobb
Előző Következő

GY-21V3-SHT20 SHT20 Hőmérséklet és páratartalom érzékelő modul Breakout átalakító

201916673816

Új termék

PCA9685 16-Channel 12 bit PWM Servo Driver I2C Interface for Arduino Raspberry
It's an i2c-controlled PWM driver with a built in clock. That means that, unlike the TLC5940 family, you do not need to continuously send it signal tying up your microcontroller, its completely free running!
It is 5V compliant, which means you can control it from a 3.3V microcontroller and still safely drive up to 6V outputs (this is good for when you want to control white or blue LEDs with 3.4 forward voltages)
6 address select pins so you can wire up to 62 of these on a single i2c bus, a total of 992 outputs - that's a lot of servos or LEDs
Adjustable frequency PWM up to about 1.6 KHz
Configurable push-pull or open-drain output
Output enable pin to quickly disable all the outputs
We wrapped up this lovely chip into a breakout board with a couple nice extras
Terminal block for power input (or you can use the 0.1" breakouts on the side)
Reverse polarity protection on the terminal block input
Green power-good LED
3 pin connectors in groups of 4 so you can plug in 16 servos at once (Servo plugs are slightly wider than 0.1" so you can only stack 4 next to each other on 0.1" header
"Chain-able" design
A spot to place a big capacitor on the V line (in case you need it)
330 ohm series resistors on all the output lines to protect them, and to make driving LEDs trivial
Solder jumpers for the 6 address select pinsPackage included: 1 x PCA9685 16 Channel 12 bit PWM Servo Driver I2C Interface f

Bővebb leírás

-4 / 14 / Gyorsan Fogyó termék

317 Ft‎

-66%

932 Ft‎

Hozzáadás a kívánságlistához

Egyéb infó

PCA9685 16-Channel 12 bit PWM Servo Driver I2C Interface for Arduino Raspberry
It's an i2c-controlled PWM driver with a built in clock. That means that, unlike the TLC5940 family, you do not need to continuously send it signal tying up your microcontroller, its completely free running!
It is 5V compliant, which means you can control it from a 3.3V microcontroller and still safely drive up to 6V outputs (this is good for when you want to control white or blue LEDs with 3.4 forward voltages)
6 address select pins so you can wire up to 62 of these on a single i2c bus, a total of 992 outputs - that's a lot of servos or LEDs
Adjustable frequency PWM up to about 1.6 KHz
Configurable push-pull or open-drain output
Output enable pin to quickly disable all the outputs
We wrapped up this lovely chip into a breakout board with a couple nice extras
Terminal block for power input (or you can use the 0.1" breakouts on the side)
Reverse polarity protection on the terminal block input
Green power-good LED
3 pin connectors in groups of 4 so you can plug in 16 servos at once (Servo plugs are slightly wider than 0.1" so you can only stack 4 next to each other on 0.1" header
"Chain-able" design
A spot to place a big capacitor on the V line (in case you need it)
330 ohm series resistors on all the output lines to protect them, and to make driving LEDs trivial
Solder jumpers for the 6 address select pinsPackage included: 1 x PCA9685 16 Channel 12 bit PWM Servo Driver I2C Interface f
201916673816 - ali110 (281)

30 egyéb termék a kategóriából: